Aj-antunes-co TTS-8 9900629 User Manual download pdf

A. J. ANTUNES & CO.

180 Kehoe Blvd., Carol Stream, Illinois 60188

USING THE TIMETECH TIMER TTS-4/TTS-8

(MFG. # 9900624, 625, 628, 629, 630, 632, 643, 644, 645 & 656)

General

If you experience any problems with these instructions,

contact the factory Technical Service Department at 630-

784-1000 or toll free in the U.S. at 877-392-7854.

The TimeTech Timer uses four or eight timing channels to

track four or eight different events simultaneously with up

to 2 timing stages for each channel.

• TTS-4(4ChannelTimer,Mfg.#9900624 & 9900630)

• TTS-8(8ChannelTimer,Mfg.#9900628,9900629,

9900632, 9900643, 9900644 9900656, & 9900645)

NOTE: While the timer can track 4–8 different timing

events at a time, as a default, it will display the timing

session that will finish first. Other active channels

can be viewed by pressing its corresponding button.

Take the Timer out of the box and allow it to charge

under a light source for 15 minutes. Do NOT obstruct

the solar cells at the front and top of the Timer or it may

not function properly.

Mounting the Timer

The TimeTech Timer mounts directly to any flat magnetic

surface with the magnetic backing. If the surface is not

magnetic,usetheprovidedUniversalMountingBracket.

1-877-392-7854 Fax: 630-784-1650 Page 1 of 4 1010878 Rev. G 08/12

Figure 1. TimeTech Timer (8 Channel Timer Shown)

1. If you are attaching the Timer to a device powered

by electricity, turn the device off, unplug the power

cord, and allow it to cool down before proceeding.

NOTE: Clean the surface where the Timer is to be

mounted thoroughly before proceeding. Observe the

proper cleaning procedures as required.

2. When mounting to a non-magnetic surface, use

theUniversalMountingBracket.Carefullypeelthe

backing from the Bracket and secure the Bracket to

the chosen mounting surface.

NOTE: The adhesive is strong. Make certain to center

it properly before attaching it to the mounting surface.

4. Attach the TimeTech Timer to the Universal Bracket.

5. If the Timer is mounted to a device, place the

device back into service.

NOTE: Do NOT obstruct the Solar Cells at the front

and top of the Timer or the Timer may not function

properly.

Idle Mode

When the Timer is not timing, the Time Display window

reads “ --:--:--.”

After 5 minutes of idle time, the Timer enters a “sleep

mode” causing the display to go blank. Press any key to

“wake up” the Timer. This will occur even if a channel is

done timing and not cleared.

Active

Channels

(Currently

Timing)

Channel

Selection

Buttons

Channel

Display

(Current

Channel)

Time Stage

Area

Enter

Button

Up/Down

Buttons

Time

Display

Enter

channel hours minutes seconds

4 5

CAUTION

Do NOT mount the timer in extremely hot (104ºF)

or wet areas. Do NOT mount the timer where it will

cause the operator to reach over hot or dangerous

equipment.

1 2 3 4

Summary of Contents

Page 1 - --:--:--.”

A. J. ANTUNES & CO. 180 Kehoe Blvd., Carol Stream, Illinois 60188USING THE TIMETECH TIMER TTS-4/TTS-8 (MFG. # 9900624, 625, 628, 629, 630, 63

Page 2 - 00:00:00, press and

A. J. ANTUNES & CO. 180 Kehoe Blvd., Carol Stream, Illinois 601881-877-392-7854 Fax: 630-784-1650 Page 2 of 4 1010878 Rev. G 08/12Programmi

Page 3 - Cleaning the Timer

Display DescriptionThis section describes the Timer display and the various functions available on the Timer. Refer to Figure 1 to identify the diffe

Page 4 - LIMITED WARRANTY

1-877-392-7854 Fax: 630-784-1650 Page 4 of 4 1010878 Rev. G 08/12LIMITED WARRANTY Equipment manufactured by Roundup Food Equipment Division of A.J.

Comments to this Manuals

No comments

Aj-antunes-co TTS-8 9900629 User Manual

Browse online or download User Manual for Kitchen Aj-antunes-co TTS-8 9900629. A.J. Antunes & Co TTS-8 9900629 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Kitchen Aj-antunes-co TTS-8 9900629