VERTICAL CONTACT TOASTERModel VCT-2000Owner’s ManualP/N 1010840 Rev. M 07/14MANUFACTURINGNUMBERS: 9210200 9210201 9210202 9210203 9210208 9210210 9210
VERTICAL CONTACT TOASTER10P/N 1010840 Rev. M 07/14Safety FeaturesHI-LIMIT RESET BUTTONA Hi-Limit Control turns off electrical power to the heat-er and
11VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14TEMPUPTEMPDOWNTEMPSCALE°F°CPOWERTEMPUPTEMPDOWNTEMPSCALE°F°CPOWERHIUSEFigure 7. “HI” Fault Message“HI
VERTICAL CONTACT TOASTER12P/N 1010840 Rev. M 07/14DailyCLEANING THE BLACK AND SILVER RELEASE SHEET, CONVEYOR BELT WRAPS, AND TOASTERTools Required: •
13VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14Replacing Belt Wraps (Every 3–6 months)NOTE: Depending on toaster usage and how well they are cleane
VERTICAL CONTACT TOASTER14P/N 1010840 Rev. M 07/14Figure 14. Removing Conveyor Belt ChainsRotationUpper Support RodLarge Link P/N 0800121Small Link P/
15VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14Weld ScrewsAcorn NutsSpacersTensioner Assy.TapeFigure 16. Replacing Roller Tensioner Assy.Figure 15.
VERTICAL CONTACT TOASTER16P/N 1010840 Rev. M 07/14TROUBLESHOOTINGWARNINGTo avoid possible personal injury and/or damage to the unit, inspection, test
17VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14TROUBLESHOOTING (continued)Problem Possible Cause Corrective ActionNo Control Display. Unit not plug
VERTICAL CONTACT TOASTER18P/N 1010840 Rev. M 07/14TROUBLESHOOTING (continued)Problem Possible Cause Corrective ActionCrowns and/or Heels must be force
19VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14Problem Possible Cause Corrective ActionToaster makes unusual sounds.Compression Settings are too t
VERTICAL CONTACT TOASTER2P/N 1010840 Rev. M 07/14GeneralThe Vertical Contact Toaster Model VCT-2000 is designed for contact toasting of buns. The toa
VERTICAL CONTACT TOASTER20P/N 1010840 Rev. M 07/14REPLACEMENT PARTSParts IdentificationPlatenHi-Limit ControlFan BladeHi-Limit Capillary ProbeA/C Freq
21VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14REPLACEMENT PARTS (continued)CAUTION Do not touch hot surfaces109108107106Heated Base OnlyC
VERTICAL CONTACT TOASTER22P/N 1010840 Rev. M 07/14REPLACEMENT PARTS (continued)POWERTEMPDOWNTEMPUPTEMPSCALE°C°F243268114321708717197020908991721512627
23VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14REPLACEMENT PARTS (continued)49941674076854251675371670787988505731191414306767959430, 9431, 9565459
VERTICAL CONTACT TOASTER24P/N 1010840 Rev. M 07/141 0011266 Conveyor Belt (Incl. Items Below) 2 0800204 1/2” Pitch Link, Small 2 0800121 3/4”
25VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14REPLACEMENT PARTS (continued) Item Part No. Description Qty.76 308P145* Nut, Hex Acorn, #8-32
VERTICAL CONTACT TOASTER26P/N 1010840 Rev. M 07/14WIRING DIAGRAMPictorial Wiring Diagram Heated Base UnitsFAN21+3-43-32 VDC240 VACINTERLOCK SWITCH# 18
27VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14WIRING DIAGRAM (continued)HI-LIMITCONTROLPOWER SWITCH240 VACLINE FILTERGL1L2S.S. RELAY 2S.S. RELAY 1
LIMITED WARRANTYEquipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been con-structed of the finest materials avai
3VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14Refer to the service agency directory included with your unit.Authorized Service AgencyName:Phone No.
VERTICAL CONTACT TOASTER4P/N 1010840 Rev. M 07/14In addition to the warnings and cautions in this manual, use the following guidelines for safe operat
5VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14BACB(no bun chute)SPECIFICATIONSElectrical SpecificationsDimensionsModel & Mfg. No.Width (A)Depth
VERTICAL CONTACT TOASTER6P/N 1010840 Rev. M 07/14WARNINGELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SE
7VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14Conveyor Safety Interlock SwitchBun Feeder (some models only)Heat ShieldRelease Sheet Retainer ClipsB
VERTICAL CONTACT TOASTER8P/N 1010840 Rev. M 07/14NOTE: The toaster is tested and shipped with the heaters set at the above recommended temperatures.OP
9VERTICAL CONTACT TOASTERP/N 1010840 Rev. M 07/14TEMPERATURE CONTROL PANELNOTE: The term “set point temperature” refers to the desired temperature set
Comments to this Manuals