Aj-antunes-co MS-250 9100439 User Manual download pdf (Page 6)

6

P/N 1010984 Rev. D 03/12

PLUMBING

NOTE: Miracle Steamer models are

designed to use cold tap water. Distilled

water may be used to reduce calcium/

mineral deposit buildup and reduce main-

tenance costs.

MS-150 MODELS

The MS-150 models have a self-contained

water tank. To fill the self-contained water

tank:

1. Open the Tank Cover on top of the

unit (Figure 3).

NOTE: Make sure filter inside tank is

installed properly.

2. Pour in cold tap water. The tank will

hold approximately 3 quarts (2.81

liters).

3. Close the Tank Cover.

NOTE: Do NOT overfill the unit’s water

tank. Only fill the tank to 90% full.

MS-250 MODELS

The MS-250 models require a direct cold

water hookup. A Water Inlet Hose and Strainer

Assembly (Figure 4) is supplied.

NOTE: Incoming water is controlled by a

normally closed (NC) solenoid valve locat-

ed inside the Steamer’s electrical housing.

1. Turn off the water valve (not supplied)

that provides water to the unit (Figure

4).

2. Connect the 1/4” (6.5 mm) I.D.

Flexible Tubing to the outlet side of

the Water Pressure Regulator and

secure using the Worm Clamp (Figure 4).

READY

Figure 3. Filling Water Tank

Filter

Tank Cover

Tank

NOTE: A Water Pressure Regulator must

first be installed (Figure 4). Failure to do

so will result in poor steaming and pos-

sible flooding. For a single steamer, use

Water Pressure Regulator P/N 7000314.

For two adjacent steamers, use Water

Pressure Regulator P/N 7000235.

3. Turn the water valve on.

4. Hold the Quick Disconnect Insert over

a bucket, then press and hold the

white plastic tip until there’s a good,

steady water flow. This will purge all

air out of the line.

5. Release the plastic tip and check

the pressure on the Water Pressure

Regulator. It should read 20 psi.

a.) If it reads less, increase the water

pressure by pulling the black knob up

and turning it clockwise.

b.) If it reads more, decrease the water

pressure by pulling the black knob up

and turning it counter clockwise.

NOTE: When adjusting the knob, you must

relieve the existing pressure by press-

ing the white plastic tip on the Quick

Disconnect Insert for 3 seconds. The Water

Pressure Regulator will then show the

new pressure.

6. Once the regulator reads 20 psi, push

the black knob down to lock it in

place.

7. Push the Quick Disconnect Insert into

the fitting at the rear of the unit until

it clicks (Figure 4).

Figure 4. Connecting Water Supply (MS-250 Only)

Connect Quick

Disconnect

Insert Here

Inlet Hose & Strainer

Assy. (Supplied)

Optional Water Pressure Regulator

with Strainer (P/N 7000314)

Shut Off Valve

(Not Supplied)

Cold

Water

Flow

Flexible Nylon Braided

1/4 " I.D. Tubing (Not Supplied)

Quick

Disconnect

Insert

Worm

Clamp

NOTE: The use of only one strainer is

acceptable instead of two.

CAUTION

Water pressure must not exceed 30 psi (2.1

kg/cm

2

or 207 kPa). Higher water pressures

may cause poor performance or flooding.

To reduce water pressure, install a water

pressure regulator, and set water pressure to

20–25 psi (1.4–1.7 kg/cm

2

or 138–172 kPa).

1 2 3 4 5 6 7 8 9 10 11 ... 19 20

Comments to this Manuals

No comments